Cres Cor Refrigerator Owner's Manual

Installation

Unpacking and Handling

Upon receiving your Cres Cor Refrigerator, it is crucial to unpack it carefully to avoid any damage. Begin by inspecting the packaging for any visible damage that may indicate potential harm to the unit. Use a box cutter or sharp knife to cut through the packing tape, taking care not to scratch the surface of the refrigerator. Once opened, remove all packing materials including styrofoam, cardboard, and plastic, and dispose of them responsibly. It's recommended to keep the user manual and any additional documentation that comes with the unit in a safe place for future reference.

When handling the refrigerator, ensure you have ample assistance, as these units can be heavy and awkward to move alone. Use a dolly or hand truck to transport the refrigerator from the delivery spot to its intended location. Be mindful of doorways and tight spaces, and never attempt to push or drag the unit as it can cause floor and structural damage.

Choosing the Right Location

Selecting the appropriate place for your Cres Cor Refrigerator is vital for optimal performance and efficiency. Choose a well-ventilated area with enough room for the refrigerator to breathe, typically leaving at least two inches of clearance on all sides and the top. Avoid placing the unit in direct sunlight or near heat sources such as ovens and radiators, as excessive heat can compromise its cooling ability and increase energy consumption.

The location should also be conveniently close to an electrical outlet. Ensure that the surface is level to prevent any operational issues, and confirm that your chosen spot allows easy access to the refrigerator doors. The area should be free of excessive moisture and should not be subject to extreme temperature fluctuations.

Electrical Requirements and Safety Precautions

Prior to powering on your refrigerator, verify the electrical requirements specified in the user manual. Typically, Cres Cor Refrigerators require a standard 120-volt, 60 Hz electrical outlet with a dedicated circuit to prevent circuit overloads.

Always use a grounded outlet and never use an extension cord or adapter, as these can lead to power disruptions and are potential fire hazards. Check the power cord for any damage before plugging it in. If any faults are detected, contact Cres Cor customer support for guidance.

Ensure the area around the refrigerator is dry and free from water spillage to prevent electrical hazards. Regularly inspect the plug and outlet for any signs of wear or damage, and address any issues immediately to ensure safety compliance.

Leveling the Refrigerator

For the refrigerator to function efficiently, it must be perfectly level. Uneven placement can lead to vibrations, increased noise, and cooling inconsistencies. Using a carpenter's level, check the horizontal positioning of the refrigerator on both the front and sides.

If adjustments are needed, locate the leveling legs at the bottom front of the unit. Most models have adjustable legs where you can rotate to raise or lower each side accordingly. For models with wheels, you may have to adjust the wheel locks in addition to using shims underneath for a steadier setting. Once leveled, recheck the balance with the carpenter's level for confirmation.

Connecting the Water Supply (if applicable)

If your Cres Cor Refrigerator model includes a water dispenser or ice maker, you will need to connect the unit to your household water supply. Ensure you have a water line connection kit, typically provided with the refrigerator or sold separately.

Begin by locating the water inlet valve on the back of the unit. Connect the provided water line to a nearby cold-water supply, using a shut-off valve that is easily accessible. Secure the line to the inlet valve, ensuring a tight fit to prevent leaks. Slowly turn on the water supply and check all connections for leaks.

For new installations, it may take a few hours for the ice maker to begin producing ice after the water line is connected. Always refer to the specific instruction manual provided with your model for detailed guidance on the water line assembly.

Final Checklist Before First Use

Before plugging in and using your Cres Cor Refrigerator for the first time, complete the following final checklist:

1. Inspection: Ensure that the unit is free from any shipment damage and that all components are intact.
2. Placement: Confirm that the refrigerator is placed in an optimal location, with appropriate spacing and level balance.
3. Electrical Setup: Double-check that the refrigerator is connected to a dedicated, grounded electrical outlet, devoid of extension cords or adapters.
4. Water Connection: If applicable, verify that the water supply is connected properly with no leaks.
5. Internal Setup: Remove any installation tape from the doors and internal shelves. Adjust shelves and compartments to the desired configuration.
6. Readiness: Allow the refrigerator to stand upright for a minimum of 4 hours before initial startup, to let the refrigerant settle.
7. Power On: Plug in the refrigerator, set the thermostat to the recommended initial temperature setting, and allow 24 hours for it to reach optimal cooling levels.

Adherence to these steps ensures that your Cres Cor Refrigerator starts efficiently and maintains longevity through proper initial setup.