John Lewis Refrigerator Owner's Manual

Installation

Unpacking Your Refrigerator

Guidelines for Safely Unpacking Unpacking your new John Lewis refrigerator requires careful handling to prevent any potential damage. Here are key guidelines to follow:

• Preparation: Ensure the space around the unit is clear before you begin unpacking. This will give you ample room to maneuver the appliance safely.
• Protective Gear: Wear protective gloves to safeguard your hands from sharp edges or packing materials.
• Use Proper Tools: Have a utility knife or scissors handy for cutting through packaging, but be mindful to avoid scratching the surface of the refrigerator.
• Safe Lifting Techniques: If the refrigerator is large, consider having an additional person to help you lift and maneuver it to reduce the risk of injury or damage.

Checklist of Items Included After unpacking, verify that all components are present and in good condition. Your package should typically include:

• Refrigerator unit
• User manual
• Warranty card
• Shelves and drawers (may come pre-installed)
• Ice maker (if applicable)
• Energy guide label
• Installation kit (if a water line is required)

Site Requirements

Recommended Room Dimensions Choosing the right space for your refrigerator is crucial for optimal performance. Ensure your room meets the following criteria:

• Width Clearance: There should be at least a 1-inch gap on either side of the refrigerator for sufficient airflow.
• Height clearance: Allow a minimum of 1 inch at the top for ventilation.
• Depth clearance: Consider leaving around 2 inches at the back for efficient heat dissipation and connecting hoses.

Ventilation Needs Proper ventilation helps your refrigerator operate efficiently. Ensure the following:

• Adequate Space: Maintain recommended clearance around the appliance.
• Avoid Enclosures: Do not place the refrigerator in tight spaces, such as alcoves, without proper ventilation.
• Temperature Control: Install the fridge in a room with controlled temperatures to avoid overworking the compressor.

Electrical Outlet Specifications Ensure a safe and stable power connection by following these guidelines:

• Dedicated Outlet: Use a dedicated grounded electrical outlet. Avoid using extension cords or adapters.
• Correct Amperage: The outlet should support the refrigerator's power requirements, typically around 115 volts and 15-20 amperes.
• Ground Fault Circuit Interrupter (GFCI): Use GFCI protection in case of power surges or moisture interference to prevent electrical mishaps.

Positioning the Refrigerator

Leveling the Appliance An uneven refrigerator can cause door misalignments and condensation issues.

• Use a Leveling Tool: Adjust the leveling screws at the base until the fridge is perfectly balanced.
• Check Both Ways: Ensure the appliance is leveled front-to-back and side-to-side.

Door Swing Clearance Consider the door swing to prevent obstructions and facilitate access:

• Measure Swing Space: Ensure sufficient clearance to fully open the doors without hitting walls or other appliances.
• Reversible Doors: If space is tight, check if door hinges can be reversed to change the door opening direction.

Anti-tip Bracket Installation For safety, install an anti-tip bracket to prevent the refrigerator from tipping forward:

• Locate the Bracket Position: Apply the bracket according to the manual’s specifications at the rear base of the appliance.
• Secure the Bracket: Mount it securely into the floor or wall structure using the provided screws and anchors.

Connecting to Power

Voltage Requirements Ensure your refrigerator operates correctly with the appropriate power source:

• Voltage Range: Utilize a 115-volt outlet to suit typical refrigerator power specifications.
• Steady Supply: Ensure a constant power supply to avoid compromising the refrigerator’s performance.

Surge Protection Advice Prevent damage from power fluctuations with these tips:

• Surge Protector: Install a dedicated surge protector to shield against voltage spikes.
• Regular Checks: Inspect connections often to ensure there are no exposed or faulty wires.

Initial Power-Up Procedure Powering up your refrigerator for the first time is crucial:

• Plugging In: Connect the refrigerator to the grounded outlet directly.
• Temperature Setting: Adjust the temperature controls to the manufacturer’s recommended levels.
• Stabilization Period: Allow the fridge to stabilize for a few hours before adding food to ensure optimal cooling.

Water Line Connection (if applicable)

Materials and Tools Required Gather necessary items for a seamless water line connection:

• Materials Needed: Water line tubing, connectors, Teflon tape
• Tools Needed: Adjustable wrench, utility knife, pliers

Step-by-Step Connection Process Follow this procedure if your model includes an ice maker or water dispenser:

1. Turn Off Water Supply: Locate and turn off your home’s water supply before starting.
2. Attach the Connector: Connect the provided water line tubing to the refrigerator’s water inlet valve.
3. Secure the Tubing: Secure the tubing to the valve using a wrench to tighten.
4. Connect to Cold Water Pipe: Attach the other end to your home’s cold water line. Use Teflon tape on threads to prevent leaks.
5. Turn On Water Supply: Gradually turn on the water supply and check the pressure.

Leak Testing Ensure connections are watertight:

• Initial Check: Inspect all connections for signs of leaks as water flows.
• Adjust as Needed: Tighten any loose connections and check each sealing.
• Final Inspection: After several hours, reinspect for drips or pooling water around the refrigerator.