How to Store and Care for Your Kambrook Iron
What Kambrook irons are and where to keep them
Kambrook is an Australian appliance brand that makes steam irons and pressing equipment for household use. If you own a Kambrook iron, storing it properly between uses keeps the heating element from corroding, prevents water damage to your refrigerator shelves (if you're storing supplies nearby), and extends the iron's working life. Unlike food, an iron doesn't belong in your fridge—but the storage principles matter just as much.
The best place to store a Kambrook iron is a cool, dry cupboard or shelf away from direct sunlight and moisture. A linen closet, pantry shelf, or dedicated appliance storage area works well. Keep it upright or on its heel rest (the small stand at the back) rather than on its side, so water doesn't pool inside the tank or drip onto surrounding items.
If you live in a humid climate or near the ocean, moisture can corrode the metal sole plate and internal components. Store your iron in a spot with good air circulation, and consider placing a small silica gel packet or moisture-absorbing sachet nearby to keep the immediate area dry.
Key Takeaways
- Store your Kambrook iron upright on its heel rest in a cool, dry cupboard away from sunlight and moisture.
- Empty the water tank completely before storing to prevent mineral buildup, rust, and leaks inside the appliance.
- Let the iron cool for at least 30 minutes after use before putting it away to avoid burns and damage to storage containers.
- Wipe the sole plate with a damp cloth while it's still warm to remove starch, fabric fibres, and mineral deposits that harden as it cools.
- Check the power cord for damage before storage and store it loosely coiled (not wrapped tightly) to prevent internal wire breakage.
Emptying the water tank before storage
Water left inside a Kambrook iron's tank will stagnate, develop mineral deposits, and eventually corrode the heating element and internal pipes. Before you put the iron away—whether for a day or a season—empty the tank completely. Most Kambrook models have a drain plug or a removable tank cap at the top or back of the unit.
To drain the tank, hold the iron over a sink with the drain hole facing downward and let gravity do the work. If your model has a removable tank, unscrew or unclip it and pour out any remaining water. Shake the iron gently to dislodge water trapped in the steam vents. Leave the tank cap or drain plug open for a few minutes so air can circulate inside and help evaporate any lingering moisture.
If you use tap water in your iron, mineral deposits build up faster. Distilled or demineralised water slows this process, but even distilled water will leave some residue over time. Emptying the tank after every use is the single most effective way to keep your iron working smoothly and prevent leaks that could damage nearby items in storage.
Cleaning the sole plate and steam vents
The sole plate—the flat metal surface that touches your fabric—collects starch, lint, and mineral deposits during use. These build up and can scratch or stick to fabric on your next ironing session. Cleaning it before storage takes two minutes and prevents problems.
While the iron is still warm (but cool enough to touch safely), wipe the sole plate with a damp cloth or soft sponge. For stubborn starch or mineral spots, use a cloth dampened with white vinegar. Wipe in the direction of the steam vents, not across them, so you don't push debris into the vents. Never use a scouring pad or abrasive cleaner—these scratch the non-stick coating and expose the metal underneath to rust.
Check the steam vents on the sole plate for lint or mineral buildup. If you see white or brown crusty deposits, soak a cloth in white vinegar and hold it against the vents for a minute, then wipe. For vents clogged with lint, a soft toothbrush or old soft-bristled brush works well. Clear vents mean steam will flow evenly when you iron next time.
Letting the iron cool safely before storage
Putting a hot iron directly into a cupboard or drawer risks burns, melts plastic storage containers, and can warp the iron's plastic housing. Always let your Kambrook iron cool for at least 30 minutes after you switch it off. Set it upright on its heel rest on a heat-resistant surface—a tile, wooden board, or metal trivet—away from fabrics, paper, or anything flammable.
Never wrap a warm iron in cloth or plastic to "speed up" cooling. This traps heat and can damage the cord insulation or the iron's casing. If you're in a hurry, set the iron in a well-ventilated spot and come back to it later. The wait is worth it: a cool iron is safer to handle, less likely to damage storage containers, and easier to inspect for any leaks or damage before you put it away.
Checking and storing the power cord
Before you store your iron, inspect the power cord for cracks, fraying, or exposed wires. If you see damage, don't use the iron—have it repaired by a may have access to technician or replace it. A damaged cord is a fire and electrical shock hazard, and storing a faulty iron makes the problem worse.
Store the cord loosely coiled or in a figure-eight loop, not wrapped tightly around the iron's body. Tight wrapping puts stress on the wires inside the cord and can cause them to break over time, leading to intermittent power loss or electrical faults. A loose coil lets the cord relax and prevents kinks. If your Kambrook iron has a cord storage clip or hook on the back, use it—that's what it's designed for.
Keep the cord away from sharp edges, hot surfaces, and moisture. If you store the iron in a damp cupboard, make sure the cord doesn't touch the back wall or any pipes where condensation might collect.
Seasonal storage and long-term care
If you're storing your Kambrook iron for several months—over summer if you don't iron much, or before moving house—take a few extra steps. Empty the tank completely and leave the cap off for 24 hours so the interior dries fully. Wipe the sole plate and vents one more time, then wrap the iron loosely in a clean, dry cloth to keep dust off without trapping moisture.
Store it in a cupboard or box in a cool room, not in a garage, shed, or attic where temperature and humidity swing wildly. Extreme heat can warp plastic parts; extreme cold can make the cord brittle. A stable indoor environment—around 15 to 25 degrees Celsius—is ideal.
Before you use the iron again after long storage, inspect the cord and sole plate, fill the tank with fresh distilled water, and test the steam on an old cloth before ironing anything you care about. If the iron has been sitting for more than six months, a quick test run catches any problems before they damage your clothes.
Troubleshooting storage-related problems
If your Kambrook iron leaks when you take it out of storage, the tank wasn't fully drained before it was put away. Empty it completely, wipe the interior dry with a cloth on a stick if you can reach it, and leave the cap off overnight. If leaking continues, mineral deposits may be blocking the drain hole—soak the drain area in white vinegar for 30 minutes, then try draining again.
If the sole plate is discoloured or rough after storage, mineral deposits have hardened on the surface. Fill the tank with equal parts white vinegar and distilled water, heat the iron to medium, and press it on an old cloth while releasing steam for 30 seconds at a time. Repeat until the sole plate looks smooth. Wipe it clean with a damp cloth and empty the tank.
If the iron won't heat up or heats unevenly, water may have corroded the heating element. This usually means the iron needs professional repair. To prevent this, always empty the tank before storage and use distilled water when you can.
Frequently Asked Questions
Can I store my Kambrook iron in the bathroom?
No. Bathrooms are humid, and moisture will corrode the sole plate and internal components. Store your iron in a dry cupboard or linen closet instead. If your only option is a bathroom, keep the tank empty, the cap off, and a silica gel packet nearby to absorb moisture.
What's the best water to use in my Kambrook iron?
Distilled or demineralised water is best because it has fewer minerals that build up and clog the heating element. Tap water works but leaves deposits faster. Never use water from a dehumidifier or air conditioner—it can contain contaminants. Always empty the tank before storage, regardless of water type.
How do I know if my iron's sole plate is damaged?
Look for deep scratches, dents, or rough patches that catch on fabric. Minor scratches are normal, but if the non-stick coating is peeling or the metal underneath is exposed, the iron may rust or stick to fabric. Have it inspected by a technician if you're unsure.
Is it safe to store my iron in a cupboard with food or dishes?
Yes, as long as the iron is completely cool and the cupboard is dry. An iron doesn't release fumes or contaminate food. Just make sure it's stable and won't tip over if someone opens the cupboard door quickly, and keep it away from anything that could be damaged by heat if the iron is accidentally left on.
What should I do if my iron won't turn on after storage?
Check that the power outlet works by plugging in another appliance. Inspect the cord for damage. If the cord looks fine, the iron may have a thermal cutout that tripped—let it sit unplugged for an hour, then try again. If it still won't turn on, it needs professional repair.