Skip to main content

How to Clean and Maintain Your Braun Juicer for Long-Lasting Performance

Braun juicers are built to handle daily use, but they need regular cleaning to stay hygienic and work well

Braun makes several juicer models, and they all share the same basic maintenance needs: prompt cleaning after each use, proper storage of removable parts, and occasional deep cleaning of the filter basket and housing. The sooner you clean your juicer after juicing, the easier the job becomes—pulp and juice dry quickly and stick hard to plastic and metal surfaces. Most Braun juicers have dishwasher-safe parts, but hand washing the filter basket and strainer extends their life significantly.

The motor housing itself never goes in water. Only the removable parts—the juice pitcher, pulp container, filter basket, and lid—should be washed. This separation protects the motor and electrical connections from moisture damage, which is the most common reason a juicer stops working.

Key Takeaways

  • Clean the filter basket and strainer immediately after juicing, before pulp dries and hardens, using warm water and a soft brush.
  • The motor housing and base should never be submerged; wipe them with a damp cloth only, and dry them right away.
  • Dishwasher-safe parts like the juice pitcher and pulp container can go on the top rack, but hand washing preserves them longer.
  • Store the juicer with the filter basket and strainer completely dry to prevent mold growth and odors inside the machine.
  • Run water through the juicer while it is running once a month to flush mineral buildup from the internal passages.

Clean the filter basket and strainer right after juicing

The filter basket is where most of the mess lives. Fruit and vegetable pulp collects in the fine mesh, and if you wait even a few hours, it hardens and becomes nearly impossible to remove without damaging the mesh. Rinse the basket under warm running water immediately after you finish juicing, holding it upside down so water flows through the mesh from the inside out.

Use a soft-bristled brush—a old toothbrush works perfectly—to gently scrub the mesh while rinsing. Brush in one direction, from the center outward, rather than scrubbing back and forth, which can tear the fine wires. Pay special attention to the edges where the mesh meets the plastic frame; pulp collects there. If you see stubborn bits, soak the basket in warm water for five minutes, then brush again. Never use a hard brush, steel wool, or abrasive sponge on the mesh.

Wash the juice pitcher and pulp container

The juice pitcher and pulp container are usually dishwasher-safe on the top rack, but hand washing them in warm soapy water takes just as long and keeps them looking new longer. Dishwashers can dull plastic over time and sometimes cause small cracks if the water pressure is very high. Wash these parts by hand with a soft sponge and mild dish soap, rinse thoroughly, and dry them completely before storing.

Check the underside of the pulp container for dried pulp stuck to the seams. These seams are where mold and odors start if moisture gets trapped. Dry the seams carefully with a cloth, or use a soft brush to reach into the corners. If you notice any discoloration or smell in the container, soak it in a solution of one part white vinegar to three parts water for 30 minutes, then scrub and rinse.

Wipe down the motor housing and base

The motor housing and base are not waterproof, so they should never be submerged or sprayed with water. Instead, unplug the juicer and wipe the outside with a damp cloth, then dry it immediately with a dry cloth. Pay attention to the area where the juice pitcher sits and where the filter basket connects to the motor; juice can drip down into these seams.

If juice has dried on the housing, dampen the cloth with warm water and let it sit on the spot for a minute to soften the residue, then wipe gently. Do not use vinegar or harsh cleaners on the plastic housing, as they can discolor or crack it. Once the housing is dry, your juicer is ready to store or use again.

Flush the internal passages once a month

Over time, minerals from tap water and tiny particles of fruit can build up inside the juicer's internal passages, which can slow the flow of juice or affect the motor's performance. Once a month, run the juicer with just water to flush these passages. Fill the hopper with room-temperature water, plug in the juicer, and let it run until the water pitcher is full. This takes about one minute and requires no disassembly.

If you live in an area with hard water (water with high mineral content), do this flush every two weeks instead. You do not need to add vinegar or cleaning solution; plain water is sufficient. After flushing, empty the pitcher and run the juicer one more time with fresh water to rinse out any loosened particles.

Store the juicer with all parts completely dry

Moisture trapped inside the juicer is the enemy. Before you put the juicer away, make sure the filter basket, strainer, juice pitcher, and pulp container are all completely dry. Set them on a clean cloth or dish rack and let them air-dry for at least 30 minutes, or wipe them dry with a lint-free cloth. Do not reassemble the juicer and store it wet.

Store the juicer in a cool, dry place—not under the sink or in a damp cabinet. If you store it in a cabinet, leave the filter basket and strainer out or store them separately so air can circulate around them. If you notice any smell coming from the juicer when you take it out, the filter basket may have trapped moisture; soak it in vinegar solution and dry it thoroughly before using the juicer again.

Replace the filter basket and strainer when they wear out

The filter basket and strainer are the parts that wear out first. After months of daily use, the mesh can develop small tears or the plastic frame can crack. Braun sells replacement baskets and strainers separately, and they are inexpensive compared to replacing the whole juicer. If you notice juice leaking from the sides of the basket during juicing, or if the mesh has visible tears, it is time to replace it.

To order a replacement, look up your specific Braun juicer model number (usually printed on the bottom of the base) and search for that model plus "replacement filter basket" or "replacement strainer." You can order these parts directly from Braun's website or through kitchen appliance retailers. Installation is simple—the basket and strainer just lift out and new ones slide in.

Frequently Asked Questions

Can I put the motor housing in the dishwasher?

No. The motor housing contains electrical components and is not waterproof. Wipe it with a damp cloth only, then dry it immediately. Submerging it will damage the motor and create a safety hazard.

What should I do if the juicer smells bad?

Soak the filter basket and strainer in a solution of one part white vinegar to three parts water for 30 minutes, then scrub with a soft brush and rinse thoroughly. Dry all parts completely before reassembling. If the smell persists, the pulp container may need the same treatment.

How often should I replace the filter basket?

With daily use and proper cleaning, a Braun filter basket usually lasts six months to a year before the mesh tears or the frame cracks. If you juice only a few times a week, it may last longer. Replace it when you see visible damage or when juice leaks from the sides during juicing.

Is it safe to use the juicer if water dripped into the motor housing?

No. Unplug the juicer immediately and let it sit unplugged for at least 24 hours in a warm, dry place so any moisture can evaporate. Do not plug it back in until you are certain it is completely dry inside. If water got inside, contact Braun customer service before using it again.

Can I soak the filter basket overnight?

Yes, soaking overnight in water or vinegar solution is safe and can help loosen stubborn dried pulp. Just make sure to dry the basket completely afterward before storing or using the juicer. Do not leave it wet, as mold can grow in the mesh.