How to Keep Your DeLonghi Juicer Clean and Working Well
DeLonghi juicers need regular cleaning to prevent pulp buildup and keep juice flowing smoothly
DeLonghi makes several juicer models, and they all work the same basic way: a motor spins a cutting disc or auger that breaks down produce, then a strainer basket or mesh screen separates juice from pulp. Over time, fruit and vegetable fibers get stuck in those screens and around the motor shaft. If you don't clean them soon after juicing, the pulp hardens and becomes much harder to remove. A few minutes of cleaning right after you juice will keep your machine running at full power and prevent the motor from working too hard.
Most DeLonghi juicer parts come apart easily by hand—no tools needed. The exact layout depends on your model, but the principle is the same: disassemble, rinse immediately, soak if needed, and dry completely before reassembling. Keeping your manual nearby during your first cleaning will show you which parts are removable and which stay attached to the motor housing.
Key Takeaways
- Clean your DeLonghi juicer within 30 minutes of juicing, while pulp is still soft and wet, not dried on.
- The strainer basket and cutting disc are the parts that trap the most debris and need the most attention during cleaning.
- Soak stubborn pulp buildup in warm water with a drop of dish soap for 10 to 15 minutes before scrubbing.
- Never put the motor base or power cord in water, and always dry every removable part completely before reassembling.
- Store your juicer with the lid off and all parts separated so air can circulate and prevent mold growth inside the housing.
Take apart your juicer right after use
Unplug the machine first. Then remove the lid, feed tube, and any pusher or plunger that came with your model. Next, lift out the strainer basket or mesh screen—this is where most of the pulp collects. If your DeLonghi has a cutting disc or auger blade, that usually lifts out next. The exact order depends on your model, so check your manual if you are unsure which parts come out and in what order.
Do not force anything. If a part feels stuck, it may be sitting on a latch or groove. Wiggle it gently side to side or rotate it slightly before pulling. Once everything is out, set the motor base and power cord aside—those never go in water.
Rinse and soak the removable parts
Hold each part under running water and use your fingers or a soft brush to rinse away loose pulp. Pay special attention to the strainer basket, because the mesh holes trap fibers easily. If the pulp is still soft and wet, rinsing alone usually works. If it has started to dry, fill a bowl or sink with warm water, add one drop of dish soap, and soak the basket and disc for 10 to 15 minutes. The water softens the dried pulp so it rinses away without scrubbing hard enough to damage the mesh.
After soaking, use a soft brush—a toothbrush works well—to gently scrub the mesh and the edges of the disc. Avoid steel wool or abrasive sponges, which can scratch the surfaces and create places where bacteria can hide. Rinse everything under running water one more time to remove all soap and pulp.
Clean the motor housing and feed tube
The motor base and feed tube should never be submerged. Instead, dampen a soft cloth with water and wipe down the outside of the motor housing and the inside of the feed tube. If pulp has dried inside the feed tube, soak a cloth in warm water and hold it against the inside for a minute or two to soften the debris, then wipe it out. For stubborn spots, use a soft bottle brush or pipe cleaner to reach inside without scratching the plastic.
Wipe the power cord with a dry cloth only—never let water near the plug or cord. If the cord has pulp on it, let the cloth be barely damp, not wet.
Dry everything completely before storing
Moisture left inside your juicer can cause mold to grow in the motor housing or on the strainer basket. After rinsing, stand all removable parts upright on a clean dish towel or drying rack so air can reach all surfaces. Do not stack them while they are still wet. Let them air-dry for at least 30 minutes, or longer if your kitchen is humid. You can speed up drying by patting them gently with a clean cloth, but make sure no moisture remains in the mesh or around the edges of the disc.
Once everything is completely dry, reassemble your juicer in reverse order—usually disc or auger first, then strainer basket, then lid and feed tube. Store it with the lid off and all parts separated so air can circulate inside the motor housing. This prevents moisture from getting trapped and keeps the machine fresh between uses.
Prevent odors and discoloration in the strainer basket
Citrus and dark fruits like beets and berries can stain the mesh basket and leave odors behind. To prevent staining, rinse the basket immediately after juicing and do not let it sit wet in a closed container. If staining does happen, soak the basket in a solution of one part white vinegar to three parts water for 15 minutes, then rinse and dry. The vinegar breaks down the pigment without damaging the mesh.
For odors, the same vinegar soak works well. You can also sprinkle baking soda on a damp cloth and gently rub the mesh, then rinse thoroughly. Never use bleach or harsh chemicals on any part of your juicer, because they can leave residue that affects the taste of your juice and may damage the plastic or rubber seals.
Store your juicer in a dry place away from direct heat
Keep your DeLonghi juicer in a cabinet or on a shelf where it will not be exposed to direct sunlight or heat from the stove. Heat can warp plastic parts and shorten the life of the motor. Humidity is also an enemy—a damp basement or kitchen corner near a sink is not ideal. If you live in a very humid climate, store the juicer with a small packet of silica gel or uncooked rice nearby to absorb moisture from the air around it.
Before you use your juicer after storing it for a while, wipe down the motor base and feed tube with a dry cloth to remove any dust. Check that all removable parts are still dry and free of mold. If you notice any musty smell, soak the basket in vinegar water again and let everything air out before juicing.
Frequently Asked Questions
Can I put DeLonghi juicer parts in the dishwasher?
Most DeLonghi juicer manuals say hand washing only for the removable parts. The dishwasher's heat and harsh detergent can warp plastic and damage the mesh strainer. Hand washing with warm water and a soft brush takes only a few minutes and keeps your parts in better condition longer.
What should I do if the juicer stops working or juices very slowly?
Slow juicing almost always means the strainer basket or mesh is clogged with dried pulp. Soak the basket in warm water for 15 minutes, then use a soft brush to clean the mesh thoroughly. If the motor does not turn on at all, check that the lid is seated correctly—most DeLonghi models have a safety switch that prevents the motor from running if the lid is not fully closed.
How often should I deep clean my juicer?
A quick rinse after every use is enough for daily cleaning. Once a week, do a deeper soak and scrub of the strainer basket and disc. If you juice daily or use your machine heavily, consider a weekly vinegar soak to prevent buildup and odors.
Is it normal for the juicer to smell like old fruit?
A slight fruity smell is normal, but a musty or sour smell means mold is growing inside. Soak all removable parts in vinegar water, clean the motor housing with a damp cloth, and let everything dry completely with the lid off. If the smell returns quickly, the motor housing may need to dry longer before reassembly.
Can I use my DeLonghi juicer for leafy greens or wheatgrass?
Most DeLonghi centrifugal juicers are designed for hard fruits and vegetables like apples, carrots, and beets. They do not work well with leafy greens or wheatgrass because those produce very little juice and clog the mesh quickly. Check your manual to see if your model is rated for soft produce before trying it.