How to Reset Your Galanz Refrigerator to Factory Settings

When and Why to Reset Your Galanz Refrigerator

A factory reset returns your Galanz refrigerator to its original settings—the same configuration it had when it left the factory. You may need to reset if the control panel is unresponsive, if you've changed settings and can't remember what they were, or if you're troubleshooting an error code that won't clear. A reset clears any custom adjustments you've made to temperature, humidity, or special modes, so use it only when other steps haven't worked.

Before you reset, know that the refrigerator will return to a standard temperature setting (usually 37°F for the fridge section and 0°F for the freezer). Any saved preferences—like a "vacation mode" or custom ice-maker settings—will be erased. Write down your current settings if you want to restore them later, or take a photo of the control panel display.

Key Takeaways

• Most Galanz models reset by holding the power button or a dedicated reset button for 3 to 10 seconds until the display flashes or goes blank.
• Check your model's user manual first, because reset procedures vary between Galanz refrigerator lines and control panel types.
• After a reset, the refrigerator will restart with factory temperature settings and may take 30 minutes to stabilize before cooling normally.
• If a reset doesn't clear an error code or restore function, the issue may be a sensor or control board fault that requires service.

Locate Your Model Number and Manual

Your Galanz model number is printed on a label inside the refrigerator, usually on the back wall or on the side wall near the top. It looks like "BCD-XXX" or similar. Write it down or take a photo. The model number tells you exactly which reset procedure applies to your unit, because Galanz uses different control panels across its product line.

Find your user manual by visiting the Galanz website or searching "[your model number] manual" online. The manual's troubleshooting or settings section will describe the reset steps specific to your refrigerator. If you can't locate the manual, contact Galanz customer service with your model number and they can send you the correct guide or walk you through the reset by phone.

Reset Using the Power Button

On many Galanz models, the simplest reset is a power-button hold. Locate the power button on your control panel—it's usually at the top left or center. Press and hold it for 3 to 5 seconds without releasing. You should see the display flash, dim, or go dark. Release the button and wait 10 seconds.

The refrigerator will beep or the display will light up again as it restarts. This is normal. The compressor may not run immediately; give the unit 30 minutes to stabilize and begin cooling. Check that the temperature display shows the factory default (usually 37°F for the fridge section) and that any error codes have cleared. If the display remains blank or unresponsive after 2 minutes, unplug the unit for 5 minutes and plug it back in.

Reset Using a Dedicated Reset Button

Some Galanz models have a small reset button separate from the power button. It may be labeled "Reset" or "RST" and is often recessed (you may need a pen or paperclip to press it). Look on the control panel itself, or check the back of the refrigerator near the power cord or compressor area.

If you find a reset button, press and hold it for 5 to 10 seconds. The display should flash or the unit should beep. Release the button and allow 30 seconds for the refrigerator to restart. The display will return to normal operation with factory settings restored. If you cannot locate a reset button, your model likely uses the power-button method instead.

What Happens After a Reset

After a successful reset, your Galanz refrigerator will restart with all settings returned to factory defaults. The temperature will be set to approximately 37°F in the refrigerator section and 0°F in the freezer. Any custom modes—such as vacation mode, energy-saver mode, or rapid-freeze—will be turned off. If you had adjusted humidity controls or ice-maker settings, those will also revert to the factory configuration.

The compressor may not run for the first 5 to 10 minutes after a reset; this is normal and allows the refrigerant to settle. After 30 minutes, the interior temperature should begin dropping. If the refrigerator still does not cool after 1 hour, or if an error code reappears, the reset did not resolve the underlying issue and you may need to contact Galanz service.

Troubleshooting If the Reset Doesn't Work

If the display remains unresponsive after you've held the power button, try unplugging the refrigerator from the wall outlet for 5 minutes. This performs a hard reset by cutting all power to the control board. Plug it back in and wait 2 minutes for the display to light up. If it still does not respond, the control panel or power supply may be faulty.

If a reset clears an error code but the code returns within a few hours, the underlying sensor or component is likely still malfunctioning. Note the error code (it will appear on the display) and contact Galanz with the model number and code. They can tell you which part is failing and whether repair or replacement is the best option. Do not attempt to reset repeatedly; each reset cycle stresses the control board.

Restoring Your Custom Settings

Once the reset is complete and the refrigerator is cooling normally, you can adjust the temperature and other settings back to your preference. Use the temperature buttons or dial on the control panel to set the fridge section to your desired temperature (most households use 35–38°F). Set the freezer to your preference (0°F is standard, but some people prefer –2°F for longer storage).

If your Galanz has special modes like vacation mode or energy-saver mode, you can re-enable them now. Refer to your manual for the button sequence or menu navigation. Take a photo of the final settings so you have a record if you ever need to reset again.

Frequently Asked Questions

Will a reset erase the ice maker settings or clear a clogged ice dispenser?

A reset returns the ice maker to factory settings but does not physically clear a blockage. If ice is stuck in the dispenser chute, you'll need to thaw it manually by pouring warm water down the chute or removing the dispenser cover and clearing the jam by hand. After clearing the blockage, the reset can help if the ice maker's control circuit was frozen or unresponsive.

How long does it take for the refrigerator to cool after a reset?

The compressor typically starts within 5 to 10 minutes of a reset. Full cooling—bringing the interior to the set temperature—usually takes 30 to 60 minutes, depending on how warm the interior was and how full the refrigerator is. Do not open the door repeatedly during this time, as it slows cooling.

Can I reset the refrigerator while food is inside?

Yes. A reset does not affect the food or require you to empty the unit. The refrigerator will continue to cool (after the restart period) and maintain food safety. However, if the refrigerator was not cooling before the reset, food may have warmed; discard any perishables that have been above 40°F for more than 2 hours.

What if the reset button is stuck or won't press?

If the reset button is recessed and won't respond to a pen or paperclip, do not force it—you may break the button or damage the control panel. Instead, use the power-button hold method. If neither method works, the control panel may be locked or faulty, and you should contact Galanz service.

Does a reset fix an error code like "E1" or "E2"?

A reset can clear an error code from the display, but if the code returns within hours, the sensor or component triggering the error is still faulty. A reset is a troubleshooting step, not a repair. If the error persists, note the code and contact Galanz with your model number so they can identify which part needs replacement.